Home > Products > Electronics & Electricity > Other Electrical & Electronic

E00/E01 piezo controllers are used to drive and control piezoelectric ceramics and nanopositioning platforms and mainly grouped into modular, integrated, industrial and board controllers with analog, digital, keyboard, I/O and other control methods. Available in open loop, closed loop, single or multiple channels. They can drive all kinds of piezoelectric products.

Characteristics

Modules

• Power amplifier module

• Sensor Control Module

• Display & Interface Module

• Chassis & Power Supply Module

Output Voltage

-20~120V, -20 ~150V, 0~300V, 0~600V, 0~900V, 0~1800V, ±120V, ±150V, ±300V, ±450V, ±900V···

Modular Combination Controller

Power Amplifier Module,Sensor Control Module,Display & Interface Module,Chassis & Power Supply Module.

Modules are freely combined into four types of A, B, C, D.

Type A:Power amplifier module Chassis & power supply module.

Type B:Power amplifier module Sensor control module Chassis & power supply module.

Type C:Power amplifier module Display & interface module Chassis & power supply module.

Type D: Power amplifier module Sensor control module Display & interface module Chassis & power supply module.

Technical Data Range

Type: E00/E01

Amplifier Module

Extended amplifier only: 1~18 channels/1~9 channels

Control analog input: Unipolar 0~+10V or 0~+5V, Bipolar -10~+10V or -5~+5V

Optional output voltage: 100V/150V/200V/300V/±150V,±200V/±300V/600V,900V/1800V/±900V

Voltage stability: < 0.1%F.S. (full scale) /8 hours

Input impedance: 100KΩ±20%

Unloaded bandwidth: Optional 1K, 10K, 30K, 50KHz

Channels/module: 1~3 channels

Ave. Power 1 channel: 7W~35W

Peak Power 1 channel: 20W~110W

Ave. Current: 40mA~350mA

Peak current: 100mA~11A

Bandwidth, small signal: 5kHz~200kHz

Bandwidth, large signal: 1kHz~50kHz

Voltage gain: 10~180 times

Knob adjustment: 10 turns

Sensor Module

Sensor type: SGS, LVDT, CAP

Sensor channels: 1~3 channels

Sensor: LEMO connector (sensor input)

Sensor output: BNC connector for 1 channel, LEMO connector for 3 channels

Sensor output voltage:Unipolar: 0~+10V, Bipolar: -10~+10V

Display/Interface Module

Channels: 1~3 channels

D/A converter: 16/24 bit ±10V output

A/D converter: 16 bit ±10V input

Output voltage resolution: 16 bit(1/30000), 24 bit(1/100000)

Communication: RS-232/RS-422/USB 2.0

Baud rate: 9600, 19200, 38400, 57600, 76800, 115200, 128000, 230400, 256000

Chassis/Power Supply Module

Power supply: AC 220V±10% 50Hz±10%

Current limit: Short circuit protection

L×H×D: 500×175×375mm/280×175×375mm

Functions

Combination: Available amplifier, sensor and interface modules, see the instructions

Feature: Modules combined freely, upgradeableBasic control way: Manual adjustment, analog input, computer serial/USB interface, spontaneous waveform control, openloop/servo control

Basic Functions: Overcurrent protection, overtemperature protection, dynamic power protection

Software configuration: Powerful standard computer control software

Spontaneous waveform: Sine, square, triangular, sawtooth wave, 1kHz-10kHz frequency with no attenuation.

LCD keyboard: Standard(LCD, membrane button, RS-232, RS-422, USB)