Home > Products > Security & Protection > Fire Fighting

 Smoke Detector conventional 2-wire EN54-7 approved 1 Smoke Detector conventional 2-wire EN54-7 approved 2 Smoke Detector conventional 2-wire EN54-7 approved 3 Smoke Detector conventional 2-wire EN54-7 approved 4
  •  Smoke Detector conventional 2-wire EN54-7 approved 1
  •  Smoke Detector conventional 2-wire EN54-7 approved 2
  •  Smoke Detector conventional 2-wire EN54-7 approved 3
  •  Smoke Detector conventional 2-wire EN54-7 approved 4

Smoke Detector conventional 2-wire EN54-7 approved

Model:YT102
Brand:ZC
Origin:Made In China
Category:Security & Protection / Fire Fighting
Label:smoke detector , fire alarm , smoke alarm en54
Price: US $6.5 / pc
Min. Order:100 pc
Inquire Now Add to Basket

Company Information

Detail

ShenZhen Zoanco Electronics Co ., Ltd

Biz MemberGuang Dong - China
Live Chat:
点击这里给我发消息Last Online:17 Jul, 2018

Product Description

2-Wire Conventional Photoelectric Smoke Detector 

GENERAL DESCRIPTION

The device is photoelectronic detector uses a state of-the-art optical sensing chamber. This detector is designed to provide open area protection and to be used with most conventional fire alarm control panel.

Two LEDs on each detector provide local 360° visible alarm indication. They flash every 3~5 seconds indicating that power is applied and the detector is working properly. The LEDs latch on in alarm. LEDs will be off when a trouble condition exists indicating that the detector sensitivity is outside the listed limit. The alarm can be reset only by a momentary power interruption. 

Specifications

Operating Voltage Range:             9 to 28VDC Volts Non-polarized

Standby Current:                   ≤60µA @ 24 VDC

Maximum Alarm Current (LED on: ) ≤30mA @ 24 VDC

Operating Humidity Range:          10% to 93% Relative Humidity, Non-condensing

Operating Temperature Range:         14°F to 122°F (-10°C to50°C)

Adjustable Sensitivity:             0.15~0.3dB/m

Height:                           2.2˝ (55 mm) installed in Base

Diameter:                              4.0˝ (103 mm)

Weight:                          5.5 oz. (155 g)

INSTALLATION

NOTE: All wiring must conform to applicable local codes, ordinances, and regulations.

NOTE: Verify that all detector bases are installed, that the initiating-device circuits have been tested, and that the wiring is correct.

Remove power from initiating-device circuits before installing detectors.

1. Wire the sensor base per the wiring diagram, Figure 1.

2. Install the sensor into the sensor base. Push the sensor into the base while turning it clockwise to secure it in place.

3. After all sensors have been installed, apply power to the control unit.

4. Test the sensor(s) as described in the TESTING section  of this manual.

5. Notify the proper authorities that the system is in operation.

 


Product Image

 Smoke Detector conventional 2-wire EN54-7 approved 1
Img 1
 Smoke Detector conventional 2-wire EN54-7 approved 2
Img 2
 Smoke Detector conventional 2-wire EN54-7 approved 3
Img 3
 Smoke Detector conventional 2-wire EN54-7 approved 4
Img 4

Send Inquiry to this Company

ShenZhen Zoanco Electronics Co ., Ltd

4F, Building B1, XinHaoSheng High-Tech Park, YongHe Road, FuYong Town, Baoan District, Shenzhen, China

Phone:
86-0755-23015236
Fax:
86-0755-23015236
Contact:
Jenny Ning (manager)
Mobile:
15220176087

Related Products of this Company

This member assumes full responsibility for the content of this listing. DIYTrade accepts no responsibility whatsoever in respect of such content.
To report fraudulent or illegal content, please click here.

China Suppliers Quick Searching:

Fire Fighting Made In China Products

,  

Fire Fighting China Suppliers and China Manufacturers