|Category:||Chemicals / Adhesives & Sealants|
|Label:||CSA tile adhesive , ceramic adhesive , adhesive|
|Min. Order:||20 mt|
|Live Chat:||Last Online:31 Jul, 2017|
Ceramic Wall and Ground CSA Tile Adhesive
“Polar Bear” tile adhesive is one kind of pre-mixed powder that based on calcium sulphoaluminate , mixed with Portland cement, other inorganic silicate materials and additive agent in a appropriate proportion.
|Bond Strength in water(MPa)||>0.5||>0.5||>1.0||>1.0|
|Bond Strength after heating and aging(MPa)||>0.5||>0.5||>1.0||>1.0|
|Bond Strength after freezing or thawing(MPa)||>0.5||>0.5||>0.5||>0.5|
|Early Bond Strength(MPa)||>0.5||>0.5||>0.5||>0.5|
|Bond Strength open time 20 minutes(MPa)||>0.5||>0.5||>0.5||>0.5|
1.High early strength and bond strength.Walking and crack-sealing after 2 hours in normal temperature.
2.Reduce working procedures.Using this product achieves effiency result without immersing.
3.Water resisitance strength and freeze-thawing strength resisitance are better than Portland cement.
4.It has excellent water retaining properties.The adhesive layer is thin and homogeneous.
5.It has good hydration under low temperature,and could be used under negative temperature according to our direction.
6.Avoid cracking ,falling off and breaking.
7.Without toxic,smell,pollution and radioactivity.
1.CSA tile adhesive make it ideal for bonding ceramic tile,fictile,slab-stone,floor tile ,ect.
2.Can beused in cold area and icehouse ,ect.
3.Can be used to bond concrete wall and stone,and eapanded polystyrence.
4.Can be used in projects which request quick hardening and time constraint situation.
|Recommendation for use||CSA TILE ADHESIVE|
|D TYPE||N TYPE||W-1 TYPE||W-2 TYPE|
|FLOOR TILE(indoor and outdoor)||*||*||*||*|
|Fa.cade ceramic tile (indoor)||*||*||*|
|Fa.cade ceramic tile(outdoor)||*||*|
The surface must be clean,dry,firm,free of dust,dirt oil and grease and be strong enough to support the weight of fixed adhesives and tiles.
New casted concrete surfaces need to be cured for a minimum of 4 weeks prior to the application of tiling.
Water the basing surface and tiles can achieve rigid adherence.
According to inverse proportion 1:0.18 to mix dry powder with clean water, using blender to mix 5 minutes. Attention clean water first then dry powder.
Need to mix enough. Leave mixture 1 minute and then light to mix round a little prior to use.
Using up the mixed material within 2 hours.
Apply the adhesive mixture to the work surface equably with a notched trowel, the thickness depend on the different thickness of tile or slab-stone . Usually lay on 2-4mm for tile and 4-6mm for slab-stone. The smoother of the work surface, the less mixture needed. Film 1 m2 each time, then press the tiles and stone in this area.
The size of notched trowel should be chosen on the roughness of work surface and tiles. The adhesive mixture shall be used on both work surface and tiles if the back of tiles are very rough or the slab-stone and tiles are relating sizable and heavy.
Filling can only be started after the adhesive mixture is dry and firm (around 12-24 hour after usage).
Tips of Usage
Special crack sealer agent should be used when filling the slot.
When working on slab-stone with size over 600×600×20mm,the uprightness is better for lower than 6m. Reinforcement is needed when over 6m.
Packing and Storage
Pack with 25kg bags.
“Polar Bear” Tile Adhesive should be stored in dry environment, and it can be stored for at least 6 months with original package.