Home > Products > Industrial Supplies > Rubber & Plastics Machine

Your Complete Tyre Retreading Equipments-Tyre Retreading Industrial Solutions Supplier

Curing Chamber /Tyre Vulcanizing Tank parameters

Specification:ML-10 Tyre Retreading Line - Curing Chamber for Truck Tyre and Passenger Bus Tires

Range of Tyre Size:Within Size of 12.00-24 Truck and Passage Bus Tyre 600-1200(16''-20''-22.5''),including Wide tyres like 385/65R22.5''

Operating Worker No.:Minimum 4 Staff required

Workshop Area: Min. 230 sqm 

Max Service Power:60kw

Curing Time:220Minutes/per shift(Timing after getting 112°C)

Max Daily Work Shift:4 shifts/day

Max Daily Output:40pcs/day

Min Required Power:380V,50HZ.,60KW

Min Required Air Supply:0.8Mpa

Min Air Compressor:1pcs(Air Displacement:1.05 m3/min;Work Prssure:1.20Mpa;Auto Power:11KW)

Min Required Air Storage:1pc(Storage Volume:1m3;Work Prssure:1.25Mpa;Temperature:100°C)

The Shandong Melion Industrial complete tyre retreading production line are mainly included:

Tyre retreading machines-Curing chamber/Vulcanizing Tank, buffing machine,tread building machine, rubber stirring machine, rubber extruding machine/extruder gun, outer envelope spreader, steel wheel rim mounting machine,rubber crumb dust collector, tyre conveyor/Monorail,repair machine,handcart,hooks,tyre initial inspection machine,all necessary accessories,etc. Also,tread rubber and cushion gum supplies.

Tyre Reteading (PRE-CURE) Curing Chamber- The tires are placed in this curing chamber and the precured tread becomes adhered to the tire through a vulcanizing process.Our wide engineering capabilities and experience enable Melion to build chambers to suit our clients' different preferences for size, steam heated, electric heated, or double heating system, semi-automatic and automatic chambers. 

The MELION Curing Chamber(autoclave) capacity available from 4 pcs,6 pcs,8 pcs,10 pcs,12 pcs ,16pcs,24 pcs tires,which satisfying different processing requirements for clients.

1. Collection of Casings 

Worn tyres are collected to select suitable casings for tyre retread. 

2. Initial Inspection 

Each tyre received in a retread plant is subjected to a rigorous visual inspection. Inspectors are assisted by the use of non-destructive sophisticated MELION inspection machine. 

3. Buffing After inspection

The tyre's old tread is mechanically removed on high speed buffers. MELION's buffers are extremely accurate and will remove the proper amount of old rubber while turning the tyre to an exact specified diameter and radius. 

4. Section Repairs & Skiving 

With advances in state-of-the-art repair materials and repair methods, many of these tyres can be routinely repaired and in most cases can be retreaded when the original tread is worn off. The repair station is where any surface injury is treated using effective material and tools for grinding and patching.

5. Cementing and Filling 

Even in small injuries it is critical that the injury is cleaned and filled. If this is not done, severe rust, separation and steel cable looseness could take tyre out of service. The injury should be inspected, and then cleaned out with a carbide cutter. After cementing the injury, a vulcanizing rubber stem should be applied to "fill" the injury. This would create a permanent repair that maximizes tyre life.

With MELION designed-and-built spray booth, your cementing operation can be executed in a clean, efficient & environmentally responsible manner.

6. Building – Tread Rubber

In the pre-cure system, the tread rubber has already been vulcanized with the new tread pattern design. The buffed tyre needs a thin layer of cushion gum to be wrapped around its crown area. The pre-cured tread rubber is then applied with the building machine. This is called the building process.

7.a) Enveloping & Rim Mounting  

 The built tyres are then mounted with envelops and rims to prepare them for curing. 

   b) or Double Envelope System

For enveloping, tyres are first fitted an outer envelope at the envelope-mounting table before the inner envelope is fitted into them. The enveloped tyres are then vacuumed out for preparation prior to curing. Modern plants have their casings hoisted by monorail systems. With professional planning from MELION engineers, you can be assured of workstations designed to maximize output and ease workflow. 

8. Curing by Chamber 

 The tyre is then placed in a curing chamber and the pre-cured tread becomes adhered to the tyre through a vulcanizing process.

Our wide engineering capabilities and experience enable MELION to build chambers to suit our clients' different preferences for size, steam heated, electric heated, or double heating system, semi-automatic and automatic chambers.

The monorail & hook system increases productivity by cutting down on chances of casings contamination and allows for faster loading and unloading of tyres. This increases your work place safety and productivity.

9. Final Inspection & Painting

The retreaded tyre is subjected to a final inspection. This inspection insures that only tyres that meet industry quality standards are allowed to leave the retread plant. All retreaded tyres are encouraged to be returned with the sidewalls painted using a light coat of black tyre paint. 

The above is the whole process flow of MELION Tyre Retreading Equipment,should you have any question or inquiry regarding our products and company,please feel free to contact us.We promise to offer you our best service with best quality products.