Product Description
| DNP Standard color Viewer |
 |
|
|
|
| The DNP Standard color Viewer is a light source which enables you to evaluate and adjust video and still cameras. With its high-frequency Fluorescent lighting method, it handles images without flicker. |
|
|
|
|
| Light source: |
DNP Standard color Viewer lamp
(Four 10W dedicated fluorescent tubes are used) |
| Power supply: |
AC100V 50, 60Hz |
| Lighting method: |
High Frequency lighting method 20KHz |
| Color rendering: |
Over 90% rendering evaluation-point for each color |
| Color temperature: |
(Measured by Minolta CL-200) |
| Operating temperature: |
10～40℃ |
| Operating humidity: |
Below 80%(avoid dew) |
| Major diameter dimension: |
375W×365H×165D m/m |
| Luminance plane dimension: |
250W×190H m/m |
| Color chart dimension: |
320W×290H m/m |
| Power consumption: |
80W |
| Weight: |
6.5kg/7.5kg |
|
|
 |
CCV-31F
CCV-51F |
|
 |
CCV-31F/G
CCV-51F/G |
|
|
|
|
| ●The Luminance plane characteristics: according to the types of self-contained fluorescent lamp |
|
| Product Type |
Luminance Color Temperature |
Lamp |
Color Temperature |
Luminance |
Color matching shift |
Weight |
| CCV-31F |
Fixed |
FL10WW-DLB |
3100K±300 |
Over 1300cd/m2 |
Within 10% |
6.5kg |
| CCV-51F |
Fixed |
FL10D-EDL-56K |
5100K±300 |
Over 1400cd/m2 |
Within 10% |
6.5kg |
| CCV-31F/G |
Volume adjustable |
FL-10WW-DLB |
3100K±300 |
Over 850～1300cd/m2 |
Within 10% |
7.5kg |
| CCV-51F/G |
Volume adjustable |
FL10D-EDL-56K |
5100K±300 |
Over 850～1400cd/m2 |
Within 10% |
7.5kg |
|
|
＊The color temperature if Luminance. Color Temperature Conversion Type viewer ranges over 50k according to the change of the Luminance.
＊The specification may change without notice |
|
|
|
|
| 【1】 |
Before using the product: |
|
| |
Power supply |
|
AC 100V, 50/60Hz shared |
| Light source |
|
10W DNP Standard color Viewer Lamp (4) |
| Power consumption |
|
80W |
|
|
| 【2】 |
Using the DNP Standard color Viewer |
|
| |
(1) |
Plug the power cable of the product into AC100V |
| |
|
| 【Precautions】 |
Do not connect any power supply other than AC100V
If the other power supply connected by accident, the inverter inside will burned out |
|
| |
(2) |
Turn on the power switch |
| |
(3) |
Lamp lights: the lamp light will stabilised after 15 to 20 minutes at the room temperature(20℃) |
| |
(4) |
If the lamp does not lit, call for Service Office for the confirmation as described on other documents. |
| |
(5) |
To suspend snaking of the lamp, press power switch 3 to 4 times [as ON/OFF]. |
|
|
| 【3】 |
If the light does not lit |
|
| |
Call for Service Office to confirm the following: |
| |
(1) |
AC 100V supplied to the wall socket. |
| |
(2) |
Plug the product into the wall socket. |
| |
(3) |
Turn the power supply switch of the product ON |
|
| |
|
 |
|
| |
Still the lamp does not lit: Consider the following: |
|
| |
|
|
|
| |
(1) |
Two of the viewer lamps lit simultaneously, one of the fuses of the inverters has blowouts. |
| |
(2) |
Four of the viewer lamps does not light means that each of the fuses of the two inverters has blowouts. |
| |
|
| 【Precautions】 |
The above occurs if the applied power supply is not AC 100V.
Fuse bum out cause internal burnout of inverter. The burned inverter needs to replace. |
|
|
|
| 【4】 |
How to replace the lamp and keep it clean |
|
| |
Place the Viewer on the flat table, and plug out the power supply cable from the wall socket.
Remove the used device in the following order: |
| |
(1) |
Unfasten the two of grub screws on the top frame. |
| |
(2) |
To remove the top frame from the main unit;
Holding 50 to 60 mm the grub screw of the top frame and press it forward. |
| |
(3) |
Remove the glass plate and acrylic plate. |
| |
|
| 【Precaution】 |
Glass plate easily breaks and may hurt your hands and fingers.
Handle the edge of the plate with care not to scratch. |
|
|
| |
◆Replacing the lamps: |
| |
(1) |
When the lamps used over 2,000 hours or one year, it needs to replace. |
| |
(2) |
Remove the Lamp Tubes: Hold the edge of the Lamp Tubes, and turn it 90 degree. |
|
| |
◆Cleaning the device: |
| |
(1) |
Impregnate alcohol to gauze then apply it onto the surface of the reflection plate / acrylic plate / glass surface to remove the dirt. |
| |
(2) |
Clean the device once in six months to one year to keep quality of the Color Temperature and Luminance. |
|
|
| 【5】 |
Other Precautions |
|
| |
Handling the viewer needs the following precautions because it contains the parts using glass. |
| |
(1) |
Do not add strong impact on the viewer |
| |
(2) |
Do not put any heavy items on the surface of the viewer |
|
Product Image
Img 1
Img 2
Send Inquiry to this Member
Related Products of this Company
This member assumes full responsibility for the content of this listing. DIYTrade accepts no responsibility whatsoever in respect of such content.
To report fraudulent or illegal content, please
click here.
China Suppliers Quick Searching:
,
