Home > Products > Electronics & Electricity > Power Supply & Distribution > Voltage Regulator

MODEL

PLN-30-9

PLN-30-12

PLN-30-15

PLN-30-20

OUTPUT

DC VOLTAGE

9V

12V

15V

20V

CONSTANT CURRENT OPERATION VOLTAGE Note.5

6.3 ~ 9V

8.4 ~ 12V

10.5 ~ 15V

14 ~ 20V

CURRENT RANGE

0 ~ 3.3A

0 ~ 2.5A

  0 ~ 2A  

0 ~ 1.5A 

RATED CURRENT

3.3A

2.5A

2A

1.5A

RATED POWER

29.7W

30W

30W

30W

RIPPLE & NOISE (max.)  Note.2

2.6Vp-p       

2Vp-p

2.6Vp-p 

2.6Vp-p

VOLTAGE ADJ. RANGE Note.5

-5% ~ 10%. Can be adjusted by internal potential meter SVR1

CURRENT ADJ.RANGE Note.5

3% ~ -25%. Can be adjusted by internal potential meter SVR2

VOLTAGE TOLERANCE   Note.3

10%

LINE REGULATION

3.0%

LOAD REGULATION

5.0%

SETUP, RISE TIME

1500ms / 230VAC 3000ms / 115VAC at full load

HOLD UP TIME (Typ.)

INPUT

VOLTAGE RANGE

90 ~ 295VAC 127 ~ 417VDC

FREQUENCY RANGE

47 ~ 63Hz

POWER FACT.or

PF 0.9 at 75 ~ 100% load, 115VAC / 230VAC

EFFICIENCY (Typ.)

80%

82.5%

83.5%

84%

AC CURRENT (Typ.)

0.4A/115VAC 0.2A/230VAC

INRUSH CURRENT (Typ.)

40A/230VAC

LEAKAGE CURRENT

<0.5mA / 240VAC

PROTECTION

OVER CURRENT

100 ~ 110%

Protection type : Constant current limiting, recovers automatically after fault condition is removed

SH.orT CIRCUIT

Hiccup mode, recovers automatically after fault condition is removed.

OVER VOLTAGE

10 ~ 14V           

14 ~ 16V 

17 ~ 22V

23 ~ 26V 

Protection type : Shut down o/p voltage, re-power on to recover

OVER TEMPERATURE

95  10  (TSW1

Protection type : Shut down o/p voltage, re-power on to recover

ENVIRONMENT

W.orKING TEMP.

-30 ~ +50 ^oC(Refer to output load derating curve)

W.orKING HUMIDITY

20 ~ 95% RH non-condensing

ST.orAGE TEMP., HUMIDITY

-40 ~ +80^oC , 10 ~ 95% RH

TEMP. COEFFICIENT

0.06%/^oC (0 ~ 50 ^oC)

VIBRATION

10 ~ 500Hz, 2G 10min./1cycle, period f.or  60min. each along X, Y, Z axes

SAFETY &EMC(Note 4)

SAFETY STANDARDS

UL879, TUV EN61347-1, EN61347-2-13, CAN/CSA C22.2 No. 223-M91(except f.or 48V), IP64 approved

WITHSTAND VOLTAGE 

I/P-O/P:3.75KVAC

ISOLATION RESISTANCE

I/P-O/P:100M Ohms/500VDC / 25 / 70%RH

EMI CONDUCTION & RADIATION

Compliance to EN55015

HARMONIC CURRENT

Compliance to EN61000-3-2 Class C (pin 25W), Class D (>70% load) ; EN61000-3-3

EMS

IMMUNITY

Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, EN61547, light industry level,  criteria A

OTHERS

MTBF

621.4Khrs min. MIL-HDBK-217F

DIMENSION

145*47*30mm (L*W*H)

PACKING 

0.22Kg; 60pcs/14.2Kg/1.25CUFT

NOTE

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25^oCof ambient temperature.

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacit.or.

Direct connecting to LEDs is not s ested f.or models with RIPPLE & NOISE>  10% and using additional drivers is highly recommended.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage. Please check the static characteristics f.or m.ore details.

5. Output voltage can be adjusted through the SVR1 on the PCB; limit of output constant current level can be adjusted through the SVR2 on the PCB.

6. Constant current operation region is within 70% ~100% rated output voltage. This is the suitable operation region f.or LED related applications, but please reconfirm special electrical requirements f.or some specific system design.

7. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC perf.ormance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

MODEL

PLN-30-24

PLN-30-27

PLN-30-36

PLN-30-48

OUTPUT

DC VOLTAGE

24V

27V

36V

48V

CONSTANT CURRENT OPERATION VOLTAGE Note.5

16.8 ~ 24V

18.9 ~ 27V

25.2 ~ 36V

33.6 ~ 48V

CURRENT RANGE

0 ~ 1.25A

0 ~ 1.12A

0 ~ 0.84A 

0 ~ 0.63A

RATED CURRENT

1.25A

1.12A

0.84A

0.63A

RATED POWER

30W

30.24W

30.24W

30.24W

RIPPLE & NOISE (max.)  Note.2

2.6Vp-p

2.3Vp-p 

4.5Vp-p

3.7Vp-p

VOLTAGE ADJ. RANGE Note.5

-5% ~ 10%. Can be adjusted by internal potential meter SVR1

CURRENT ADJ.RANGE Note.5

3% ~ -25%. Can be adjusted by internal potential meter SVR2

VOLTAGE TOLERANCE   Note.3

10%

LINE REGULATION