Model: | - |
---|---|
Brand: | tri band signal repeater |
Origin: | Made In China |
Category: | Electronics & Electricity / Telecommunication & Broadcasting / Network Communications Equipment |
Label: | mobile phone signal , tri-band mobile phon , umts signal repeater |
Price: |
US $330
/ pc
|
Min. Order: | 1 pc |
Live Chat: | Last Online:14 Apr, 2015 |
· 2G/3G/4G cellphone signal booster ,tri band signal repeater ,tri band signal amplfier
900 1800 2100MHz signal repeater GSM & DCS & 3G wireless signal repeater
Are you are faced problem with your mobile network?
We are here to help provide you with a wide range of repeater that will boost your mobile phone signal , And make you contact with others smoothly.
Key specifications of our tri-band repeater for 900/1800/2100MHz
Items |
Uplink |
Downlink |
|
FrequencyRange |
GSM900+DCS+WCDMA |
890 ~ 915 MHz |
935 ~ 960 MHz |
1710 ~ 1785 MHz |
1805 ~ 1880 MHz |
||
1920 ~ 1980 MHz |
2110 ~ 2170 MHz |
||
Max.Gain |
70 ~ 75 dB |
65 ~ 75dB |
|
Manual Gain Control |
31dB in step of 1dB |
||
Automatic Gain Control |
20dB |
||
Bandwidth |
Wide Band |
||
Ripple in Band |
CDMA/GSM 8dB DCS10dB WCDMA 6dB |
||
Max. Input Power Without Damage |
0 dBm |
||
Output Power |
UL20dBm/DL23 dBm |
10 ~ 24 dBm |
|
Intermodulation Products |
9KHz~1GHz |
-36 dBm |
-36 dBm@Po20dBm |
1GHz~12.75GHz |
-30 dBm |
-30 dBm@Po20dBm |
|
Spurious Emission |
9KHz~1GHz |
-36 dBm |
-36 dBm |
1GHz~12.75GHz |
-30 dBm |
-30 dBm |
|
Spurious Emission Mask( WCDMA ) |
Complies with 3GPP TS 25.106 |
||
Modulation Accuracy( WCDMA ) |
Complies with 3GPP TS 25.106 |
||
Peak Code Domain Error( WCDMA ) |
Complies with 3GPP TS 25.106 |
||
ACRR( WCDMA ) |
30dB ±5MHz±10MHz |
||
Noise Figure @ max. gain |
8 dB(Typical) |
||
Return loss |
- 8 dB |
||
Time Delay |
0.5 μs |
||
MTBF |
50000 hours |
||
Power Supply |
AC 90~265V, 50/ 60Hz DC 12V 10A |
||
Power Consumption |
55W |
||
Impedance |
50 ohm |
||
Input Signal Level |
Normal |
At the edge of green and orange -50dBm or more |
|
Low |
Green |
||
High |
1-5dB range Orange 20dB Red |
The full set may include (the accessories is up to your choice)
ST repeater main unit
◆Outdoor antenna
◆Indoor antenna
◆Feeder line
◆Power Splitter (when there are more than 2 indoor antennas)
◆Connector(N connector, F connector, N to F connector etc)
Installation guide:
Installation Steps
1 Use of mobile phones at the top of building or around the building to check out the direction of the strongest signal location.
2 Select the appropriate location, and put the outdoor antenna fix to the wall or bracket.
3 Select the appropriate location of the indoor locations (this location could be best that close to power and a well-ventilated place, sun-proof, rain-proof) Install the Indoor Repeater, and fix on wall or bracket.
4 Put the outdoor antenna to the "OUT DOOR" connector and tightens it. Thus complete the outdoor antenna and Repeater's connection.
5 After setting the suitable location of the indoor antenna and the installation place, then fixing the antenna.
6 The indoor antenna and Repeater wiring, the indoor antenna connect one end of the interface and on the other end connect Repeater's "IN DOOR" port.