Home > Products > Industrial Supplies > Construction Machine

Custom processing: it is type: brick machine cycle: 15 (in seconds)

Mode of transmission: hydraulic vibration frequency: 1400 (times/min) maximum pressure: 250 (KN)

The weight: 5.6 (t) vibration frequency: 50 (hz) working pressure: 20 (Mpa)

Dimension: 380 * 200 * 200 (cm) capacity: 36.4 (kw) of the molding pressure: 250 (t)

Main vibration form: the vibration table total power: 36.4 (w) : brand wins the brand

Model: QT6-15 alias: brick block molding machine use: production of brick wall

The main technical characteristics:

1, the PLC intelligent control, using the data transmission device, the control system configuration security logic control and fault diagnosis system, and has the remote technical support etc.

2, skip unique rotating cutting device, thoroughly solve the porous brick fabric problem.

3, vibration adopt hydraulic motor, solve motor heating problem, vibration frequency through the proportional valve is adjustable, and USES the original research of the hydraulic oil, make the machine more reliable and stable.

4, this machine is suitable for production of high quality, high strength concrete or fly ash brick, high strength chain terminal brick, such as adding a color fabric cloth machine, to produce various color such as floor tile surface.

5, multi-usage, change the mold to produce various specifications of hollow block, the standard bricks, porous brick, insulating brick, cement products, etc.

For color pavement brick, grass brick, slope protection brick production such as customizing, automatic secondary cloth, fabric to add automation is realized

Matters needing attention

A lump "extremely easily, hopper for cement, so material increases with the increasing to use, not easy storage time is too long.

Second, feeding, feeding, must pay attention to mix cannot have large aggregate (more than 10 mm in diameter), especially iron fortified items, easy to damage the mold and mechanical parts.

Third, check whether the brick plate is clean, found bonding pad, will only be sent to shovel machine plate box.

Four, pressure to strictly control the vibration time (3-5 seconds), high speed feed when necessary. Pay attention to the process at any time limit is normal, whether the screw is loose. If you have an accident, timely stop adjustment.

Five, the hydraulic system should be transferred to the rated pressure (12-16 mpa), cleaning oil screen on schedule, the oil filter at least once a year. Always check the actual amount of oil tank, complement when necessary.

Six, sliding sleeve and vertical wear transition to replace nylon or copper, ensure molding box and pressure head quadrilateral gap roughly uniform, smooth demoulding.

Seven, for the hopper bottom to keep consistent with the mould surface, using a certain period of time should be checked, after high speed for the hopper back, can back to the remaining material, also can clear the head surface sticky material, scraper to set up and down, wear the transition should be timely conversion.

Machine maintenance maintenance

One, should be inspected carefully before they are using the machine all fasteners are loose; The lubrication part should lubrication as required.

Second, check whether the machine control system is normal? Limit switches and control component failure?

Three, check the bottom size, not eligible are not allowed to be used, lest jam damage the machine.

Four, after each shift production to mould box, pressure head and other parts of the machine on the residual concrete clean.

Five, the appearance of all components in the system as far as possible to keep clean (no putty accumulation) the outer surface of the tank should be cleaned on a regular basis.

Sixth, adhere to the daily maintenance and regular maintenance.

Maintenance: maintenance: 1. The shift to inspect the equipment parts, before starting the handover good lubricating by the regulation, add grease, application Settings. 2. Maintenance: use process in strict accordance with the operation procedures using machines, observe its operation situation, found that exception to stop processing in a timely manner. 3. After the maintenance: to make full use of time, get everything within the scope of the cleaning operation.

Regular maintenance: 1. Remove the set of components, lid and fence etc, thoroughly clean, wipe the equipment inside and outside. 2. Parts clearance adjustment, tighten loose parts, check the wear parts, replacement of individual parts. 3. Check the oil, circuit, water; Regularly clean the guide rail and sliding guide rod parts, deburring and scratches.

Seven, abide by the concrete block machine operation and maintenance system of the four requirements:

Tidy: including tooling, mold, tool accessories neatly placed, security devices, complete line pipes.

Cleaning: production line equipment, the operation scope of work clean, do four leakage (no leakage, no leakage, no leakage, no leakage material).

Lubricating timing: come on, add grease, cursor is bright.

Security: a personal set machine and the system of succession, abide by rules of operation and maintenance, and careful maintenance, monitoring different shape.

Concrete block molding machine USES and characteristics

(a) purpose:

Used in the production of all kinds of terminal brick, brick road, lane brick, tile, grass brick, square brick, road shoulder, lu yanshi, river, slope protection, the pavement brick, all kinds of grass brick wall of small block, parking lot, can meet the market demands.

(2) features:

1, the machine for hydraulic transmission, compression molding (vertical orientation) vibration, thus forming effect is good, can fold 4-5 layer maintenance.

2, hydraulic, mechanical subsidiary, complete the process, so cycle is short, the molding cycle is 11 to 25 seconds (need to add the fabric long time).

3, vibration mode, vibration (compactness good).

4, intelligent, high yield, multi-usage (do different types of brick, as long as the mould replacement).

5, pressure rated 12-20 mpa.

(3) the concrete porous brick features:

In line with the current building model

Meet the needs of different parts, function

To facilitate the secondary decoration

Improve block permeability, shear and seismic performance

Improve the thermal performance of block

To prevent the cracks of the wall

Construction is convenient

Economic benefit is remarkable